BS EN 1053 1996
|
ID： |
557A36DB0A50485CBBE0EEB02225F730 |
|
文件大小(MB)： |
0.07 |
|
页数： |
10 |
|
文件格式： |
|
|
日期： |
2013-7-8 |
|
购买： |
文本摘录（文本识别可能有误，但文件阅览显示及打印正常，pdf文件可进行文字搜索定位）：
BRITISH STANDARD BS EN,1053 : 1996,BS 2782 :,Part 11 :,Method 1112B :,1996,The European Standard EN 1053 : 1995 has the status of a,British Standard,ICS 23.040.20,NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW,Plastics piping systems –,Thermoplastics piping systems,for non-pressure,applications –,Test method for,watertightness,Licensed Copy: Institute Of Technology Tallaght, Institute of Technology, Sun Oct 22 00:53:48 GMT+00:00 2006, Uncontrolled Copy, (c) BSI,This British Standard, having,been prepared under the,direction of the Sector Board for,Materials and Chemicals, was,published under the authority of,the Standards Board and comes,into effect on,15 August 1996,ó BSI 1996,The following BSI references,relate to the work on this,standard:,Committee reference PRI/61,Draft for comment 92/52897 DC,ISBN 0 580 25545 X,BS EN 1053 : 1996,Amendments issued since publication,Amd. No. Date Text affected,Committees responsible for this,British Standard,The preparation of this British Standard was entrusted by Technical Committee,PRI/61, Plastics piping systems and components, upon which the following bodies,were represented:,British Gas plc,British Plastics Federation,British Plumbing Fittings Manufacturers' Association,British Valve and Actuator Manufacturers' Association,Department of the Environment (British Board of Agre?ment),Department of the Environment (Building Research Establishment),Department of the Environment (Property and Buildings Directorate),Department of Transport,Electricity Association,Federation of Civil Engineering Contractors,Health and Safety Executive,Institute of Building Control,Institute of Materials,Institution of Civil Engineers,Institution of Gas Engineers,Institution of Water and Environmental Management,National Association of Plumbing, Heating and Mechanical Services Contractors,Pipeline Industries Guild,Plastics Land Drainage Manufacturers' Association,Society of British Gas Industries,Society of British Water Industries,Water Companies Association,Water Services Association of England and Wales,The following bodies were also represented in the drafting of the standard, through,subcommittees and panels:,Engineering Equipment and Materials Users' Association,ERA Technology Ltd.,RAPRA Technology Ltd.,Licensed Copy: Institute Of Technology Tallaght, Institute of Technology, Sun Oct 22 00:53:48 GMT+00:00 2006, Uncontrolled Copy, (c) BSI,BS EN 1053 : 1996,ó BSI 1996 i,Contents,Page,Committees responsible Inside front cover,National foreword ii,Foreword 2,Method,1 Scope 3,2 Principle 3,3 Apparatus 3,4 Test pieces 3,5 Procedure 3,6 Test report 3,Figure,1 Typical arrangement 4,Licensed Copy: Institute Of Technology Tallaght, Institute of Technology, Sun Oct 22 00:53:48 GMT+00:00 2006, Uncontrolled Copy, (c) BSI,ii ó BSI 1996,BS EN 1053 : 1996,National foreword,This British Standard has been prepared by Technical Committee PRI/61 and is the,English language version of EN 1053 : 1995 Plastics piping systemsD Thermoplastics,piping systems for non-pressure applicationsD Test method for watertightness,published by the European Committee for Standardization (CEN).,It is incorporated into BS 2782 Methods of testing plastics: Part 11: Thermoplastics,pipes, fittings and valves, as Method 1112B : 1996 for association with related test,methods for plastics materials and plastics piping components.,This test method has been prepared for reference by other standards under,preparation by CEN for specification of plastics piping systems and components. It has,been implemented to enable experience of the Method to be gained and for use for,other fresh applications.,It is also for use for the revision or amendment of other national standards as,practicable, but it should not be presumed to apply to any existing standard or,specification which contains or makes reference to a different test method until that,standard/specification has been amended or revised to make reference to this Method.,This Method supersedes BS 2782 : Part 11 : Method 1112A : 1989, which becomes,obsolescent except for supporting references thereto in BS 4576 : Part 1 : 1989,BS 4660 : 1989 and BS 5255 : 1989.,The principal technical differences between EN 1053 : 1995 and BS 2782 : Part 11 :,Method 1112A : 1989 are as follows.,Parameter EN 1053 : 1995 BS 2782 : Part 11 :,Method 1112A : 1989,a) Ambient temperature,during test piece,assembly and testing,(23 ± 5) êC 15 êC to 35 êC,b) Angular deflection,applied to the joint,under test,Yes, if deflection is,possible, to maximum,declared for the joint by,its manufacturer,Not specifically required,unless specified by the,product spec……
……